TX 4x4
Written quote Get a quote

Toyota Tundra Lift Kit

A suspension lift kit for the Toyota Tundra that raises the half-ton for 35s, with the control arms, driveshaft work and alignment a full-size coil-over front needs.

A suspension lift kit hardware set laid out on a bright shop apron

Toyota Tundra Lift Kit at a glance

Two-inch Tundra lift with spacers and shocks
$1,200–$2,200
Two-and-a-half to three-inch Tundra suspension lift
$1,900–$3,200
Three-inch Tundra lift with upper control arms
$2,600–$4,000
Four-wheel alignment after the lift
$95–$190

Toyota Tundra lift kit sized for a full-size half-ton

The Tundra outweighs the Tacoma and loads its front coil-over harder, so a lift built for a midsize would sag under the half-ton. We lift the Tundra nose on thicker coils and the tail with a lift block or an added leaf, then correct the camber and driveshaft angle the extra height upsets. It finishes level, on 35s, and still steady with a trailer hitched.

  • Two to three inches that supports the Tundra's nose weight
  • Front coil or coil-over upgrade, not a spacer that sags
  • Driveshaft and steering correction for the taller half-ton
A suspension lift kit hardware set laid out on a bright shop apron

Toyota Tundra lift kit fitment

The second- and third-generation Tundras have different front ends, and a 2022-and-newer truck needs its own coils and struts. We confirm generation, cab, bed length and whether the truck carries the TRD package before the parts list is set.

  • Second-generation Tundra, 2007 through 2021
  • Third-generation Tundra from 2022
  • Lift of 2 to 3.5 inches depending on tire size
  • CrewMax and Double Cab, two- and four-wheel drive, TRD trims

What the Tundra lift kit includes

A half-ton lift is heavier hardware than a midsize one, and the list is sized to the Tundra's weight and use rather than lifted from a smaller kit.

  • Front coil spacers or replacement coil-overs for the Tundra
  • Rear lift block or add-a-leaf for the Tundra leaf pack
  • Longer shocks valved for the Tundra's weight
  • Upper control arms that restore camber range
  • Carrier-bearing spacer where the driveshaft angle needs it
  • Brake-line brackets, sway-bar links and a torque sheet

How we install a Toyota Tundra lift kit

The Tundra follows the same steps each visit, so the heavy truck finishes aligned and smooth.

  1. 1. Confirm the Tundra generation, cab, bed and target height.

  2. 2. Measure the ride height and inspect the front coil-overs and leaf springs.

  3. 3. Fit the front coils and corrected upper control arms.

  4. 4. Set the rear with a block or an add-a-leaf.

  5. 5. Install the longer shocks and reset the sway-bar links.

  6. 6. Align camber, caster, toe and thrust on the Tundra.

  7. 7. Road-test under load, check driveshaft angle and re-torque.

What a Toyota Tundra lift kit costs

A Tundra lift runs higher than a midsize job, since the coils and dampers carry a heavier truck and the geometry parts are beefier. Numbers shift by generation and trim, so take them as a guide and ask us to quote your truck. Numbers vary by year and trim.

Two-inch Tundra lift with spacers and shocks
$1,200–$2,200 installed
Two-and-a-half to three-inch Tundra suspension lift
$1,900–$3,200
Three-inch Tundra lift with upper control arms
$2,600–$4,000
Four-wheel alignment after the lift
$95–$190
Rear add-a-leaf for a loaded Tundra
$450–$1,000

What a lifted Tundra demands

Weight is why a full-size lift is not a scaled-up midsize job. Lift a Tundra on undersized hardware and the front coils settle, the included angle goes off and the truck eats front tires. Corrected arms, properly valved shocks and a driveshaft-angle check are what keep a lifted half-ton working instead of wandering down the expressway.

  • Coils and shocks rated for the Tundra's curb weight
  • Front camber held in range with corrected arms
  • A driveshaft kept quiet under a trailer load

From the bay

Questions about this build

How much lift can a Tundra take?

Two to three inches is the sweet spot on a Tundra, because the front coil-over keeps travel and the driveshaft angle stays healthy. Past three the half-ton needs corrected arms and driveshaft attention, which we price into the quote.

Will a lifted Tundra ride rough?

It can if the shocks are wrong for the load. We valve the shocks for the Tundra's weight so the truck stays planted without riding like a dump truck, which is the balance a full-size lift lives or dies on.

Do I need new upper control arms on a lifted Tundra?

Past three inches, yes. The stock Tundra arms run out of ball-joint range and cannot hold camber, so corrected arms are the only way to align it. Under that, originals are usually fine.

Can you lift a two-wheel-drive Tundra?

Yes, and a two-wheel-drive Tundra lifts cleanly for stance and front clearance. The front hardware differs from the four-wheel-drive kit, so we order by the drivetrain and confirm the springs first.

What tires fit a three-inch Tundra lift?

A three-inch lift usually clears a 35 on a Tundra with the right offset, and a 33 without effort. We check wheel offset and fender clearance on your truck so the tire you want actually fits.

How does a lifted Tundra tow?

Well, when the rear is supported properly. We keep the rear leaf pack working and add a block or an add-a-leaf so the loaded Tundra stays level instead of squatting, which keeps the steering light and the trailer tracking straight.

Why Valley drivers bring their trucks here

  • Lift, leveling, wheels and alignment under one roof, corrected and aligned.
  • Written estimate before any part is ordered, with the extras called out.
  • Fitment confirmed on your exact truck before you buy tires or wheels.
  • Road-tested and re-torqued, with a settling check after the first miles.

Request a quote

Tell us your truck and what you want. We reply with a written quote for the build.