TX 4x4
Written quote Get a quote

RAM 1500 Lift Kit

A suspension lift kit for the RAM 1500 that raises the coil-spring half-ton for 35s, keeping the rear coils and the ride that sets a Ram apart.

A coil-over shock and lift blocks laid out on a bright installation bay floor

RAM 1500 Lift Kit at a glance

Two-inch RAM lift with spacers and shocks
$1,250–$2,200
Two-and-a-half to three-inch RAM suspension lift
$1,950–$3,200
Three-inch RAM lift with upper control arms
$2,700–$4,000
Four-wheel alignment after the lift
$95–$190

RAM 1500 lift kit that keeps the coil-spring ride

Because the RAM 1500 runs coils at the rear, a lift kit has to be built differently than a leaf-spring truck's. We raise the Ram front with taller coils or coil-overs and the rear with taller coils or a small spacer, fit corrected arms past three inches and check the geometry the height changes. The half-ton gains clearance for 35s and keeps the plush coil ride that made a Ram worth buying.

  • Two to three inches that keeps the Ram's coil ride intact
  • Rear coil handling rather than a leaf block
  • Arms and driveshaft angles corrected for the height
A coil-over shock and lift blocks laid out on a bright installation bay floor

RAM 1500 lift kit fitment

The DT Ram from 2019 and the older DS trucks take different lift hardware, and an air-suspension Ram needs a kit that works with its height sensors rather than one that ignores them. We confirm the generation, trim and suspension type first.

  • DS-generation RAM 1500, roughly 2009 through 2018
  • DT-generation RAM 1500 from 2019
  • Lift of 2 to 3.5 inches depending on tire size
  • Two- and four-wheel drive, coil and air-suspension trucks

What the RAM 1500 lift kit includes

On a Ram the rear coils are the interesting part, so the kit works with them rather than replacing them with a crude block. The front gets corrected arms so the half-ton can still be aligned.

  • Front coil spacers or replacement coil-overs for the Ram
  • Taller rear coil springs or a coil spacer for the half-ton
  • Longer shocks matched to the Ram's travel and weight
  • Upper control arms that restore camber range
  • Ride-height-sensor and brake-line attention for air-sprung Rams
  • A full torque sheet and a road test at the finish

How we install a RAM 1500 lift kit

The Ram goes up in a fixed sequence so the coil-spring half-ton keeps its ride and still aligns at the new height.

  1. 1. Confirm the RAM generation, trim and suspension type.

  2. 2. Check the ride height and inspect the front struts and rear coils.

  3. 3. Install the front lift and the corrected upper arms.

  4. 4. Set the rear height with taller coils or a spacer.

  5. 5. Fit the longer shocks and check the brake lines.

  6. 6. Align camber, caster, toe and thrust at the new height.

  7. 7. Road-test for ride, wander and vibration, then re-torque.

What a RAM 1500 lift kit costs

A Ram lift is coils, dampers and whichever arms the height forces, and the total grows most past three inches. Figures shift with the generation and trim, so take the ranges as a guide and have us quote your Ram. The total varies by year and trim.

Two-inch RAM lift with spacers and shocks
$1,250–$2,200 installed
Two-and-a-half to three-inch RAM suspension lift
$1,950–$3,200
Three-inch RAM lift with upper control arms
$2,700–$4,000
Four-wheel alignment after the lift
$95–$190
Rear coil upgrade for a loaded Ram
$500–$1,050

What a lifted RAM 1500 demands

Lifting a Ram past three inches without corrected arms leaves the truck unable to hold camber, and skipping the geometry check on an air-sprung truck confuses the height sensors. Because the coil rear is softer than a leaf pack, the shocks have to do more of the work, so matching them to the Ram's weight is what keeps a lifted truck comfortable instead of floaty.

  • Camber held where the Ram can align to it
  • Air-suspension sensors left working correctly
  • Shocks matched so the coil ride stays plush

From the bay

Questions about this build

How much can you lift a RAM 1500?

Two to three inches is the sensible range, because the front suspension keeps travel and the coil rear stays comfortable at that height. Past three the Ram needs corrected arms and often driveshaft work, and we build those into the quote.

Will lifting a RAM 1500 ruin the coil ride?

Not if the kit is built for the coil rear. We use taller coils and matched shocks rather than a crude leaf-style block, so a lifted Ram keeps the plush ride that sets it apart from a leaf-spring truck.

Can you lift an air-suspension RAM?

Yes, with the right parts. An air Ram rides on height sensors, so we fit a kit that respects them and recheck the ride height after installation. Tell us the truck has air springs and we plan the lift around them.

Do I need new upper control arms on a lifted RAM?

Past about three inches, yes. The stock RAM arms run out of ball-joint range and cannot hold camber, so corrected arms are the only way to align it. Below that, originals are usually fine.

What tires fit a three-inch RAM lift?

A three-inch lift usually clears a 35 on a RAM with the right offset, and a 33 without effort. We check wheel offset and fender clearance on your truck before any tire is ordered.

Does lifting a RAM 1500 affect its towing?

Handled correctly, no. We keep the rear coils working and add a coil spacer or taller coils so a loaded Ram stays level rather than sagging, which keeps steering light and the trailer tracking straight.

Why Valley drivers bring their trucks here

  • Lift, leveling, wheels and alignment under one roof, corrected and aligned.
  • Written estimate before any part is ordered, with the extras called out.
  • Fitment confirmed on your exact truck before you buy tires or wheels.
  • Road-tested and re-torqued, with a settling check after the first miles.

Request a quote

Tell us your truck and what you want. We reply with a written quote for the build.