Ford F-150 Lift Kit
A suspension lift kit for the Ford F-150 that raises the half-ton for 35s, with the control arms, driveshaft correction and alignment a body-on-frame truck needs to stay civil on the road.
Ford F-150 Lift Kit at a glance
- Two-inch F-150 lift with spacers and shocks
- $1,150–$2,100
- Two-and-a-half to three-inch F-150 suspension lift
- $1,800–$3,000
- Three-inch F-150 lift with upper control arms
- $2,500–$3,900
- Thrust and four-wheel alignment after the lift
- $95–$190
Ford F-150 lift kit that keeps a half-ton civil
A lifted F-150 gets a bad name because tall trucks with stock arms and no alignment shake and wander. We raise the F-150 with coils or coil-overs up front and a block or add-a-leaf out back, fit corrected upper control arms so camber holds, and check the driveshaft angle the extra height changes. The truck gains real clearance and still steers like the truck its owner drives every day.
- Two to three inches with the front geometry corrected
- Corrected upper control arms so camber stays in range
- Driveshaft and steering checked for the new height
Ford F-150 lift kit fitment
The 2015 aluminum switch changed the front and rear hardware, so a kit for a 2013 does not bolt onto a 2019. We confirm the generation, the powertrain and the rear axle, because an F-150 with a long bed or the HDPP package is sprung heavier and takes a different rear block.
- Twelfth-generation F-150 through 2014
- Thirteenth-generation aluminum F-150, 2015 through 2020
- Fourteenth-generation F-150 from 2021
- Lift of 2 to 3.5 inches depending on tire size
- Two- and four-wheel drive, standard and heavy-duty payload packages
What the Ford F-150 lift kit includes
On a half-ton the arms and the shocks carry the weight, so the parts list is chosen for the truck's engine and bed rather than copied from a lighter F-150. Nothing here is a one-size disc.
- Front coil spacers or replacement coil-overs for the F-150
- Rear block with the right taper, or an add-a-leaf
- Longer shocks valved for the F-150's curb weight
- Upper control arms that restore camber adjustability
- Carrier-bearing spacer for the rear driveshaft
- Sway-bar end links, brake brackets and a torque sheet
How we install a Ford F-150 lift kit
An F-150 lift runs in a set order, so the heavier half-ton comes off the rack aligned and free of the shake people blame on lifts.
-
1. Confirm the F-150 generation, engine, bed and target height.
-
2. Measure the four corners and inspect the struts and leaf springs.
-
3. Install the front lift and the corrected upper control arms.
-
4. Set the rear with a block or an add-a-leaf.
-
5. Fit the longer shocks and the sway-bar end links.
-
6. Align camber, caster, toe and thrust at the raised height.
-
7. Road-test, watch for driveshaft vibration and re-torque.
What a Ford F-150 lift kit costs
An F-150 lift is the kit plus the labor plus the geometry parts the height makes mandatory, and it jumps once you pass three inches. Figures differ by generation and trim, so treat them as ranges and let us quote the exact half-ton. The figure varies by year and trim.
- Two-inch F-150 lift with spacers and shocks
- $1,150–$2,100 installed
- Two-and-a-half to three-inch F-150 suspension lift
- $1,800–$3,000
- Three-inch F-150 lift with upper control arms
- $2,500–$3,900
- Thrust and four-wheel alignment after the lift
- $95–$190
- Rear add-a-leaf for a loaded F-150
- $450–$950
What changes under a lifted F-150
Once an F-150 climbs toward three inches, the stock control arms run out of ball-joint range and camber goes where it likes, and the two-piece rear driveshaft starts to work at a sharper angle. Those two things, not the springs, are why an F-150 sometimes shudders after a lift. Corrected arms and a carrier-bearing spacer are what put it right.
- Camber held where the F-150 can align to it
- Rear driveshaft kept from shuddering under acceleration
- An F-150 that tracks straight instead of hunting the lane
From the bay
Questions about this build
How much lift can an F-150 take?
Two to three inches is the sensible range on an F-150, because the front coil-over keeps travel and the rear driveshaft angle stays healthy. Past three the half-ton needs corrected arms and driveshaft attention, which we build into the quote.
Will lifting an F-150 make it ride rough?
It can if the shocks are wrong for the weight. We valve the shocks for the F-150's engine and bed so the truck stays planted without crashing over expansion joints, which is the balance a half-ton lift lives on.
Do I need new upper control arms on a lifted F-150?
Past about three inches, yes. The stock F-150 arms run out of ball-joint range and cannot hold camber, so corrected arms are the only way to align it. Below that, originals are usually fine.
What tire fits a three-inch F-150 lift?
A three-inch lift usually clears a 35 on an F-150 with the right offset, and a 33 without effort. We check wheel offset and fender clearance on your truck before any tire is ordered so the set actually fits.
Can you lift a two-wheel-drive F-150?
Yes, and a two-wheel-drive F-150 lifts cleanly for stance and clearance. The front hardware differs from the four-wheel-drive kit because the spindles and knuckles are not the same, so we order by the drivetrain you have.
How does a lifted F-150 tow?
Well, when the rear is supported properly. We keep the rear leaf pack working and add a block or an add-a-leaf so a loaded F-150 stays level rather than squatting, which keeps steering light and the trailer tracking straight.
Why Valley drivers bring their trucks here
- Lift, leveling, wheels and alignment under one roof, corrected and aligned.
- Written estimate before any part is ordered, with the extras called out.
- Fitment confirmed on your exact truck before you buy tires or wheels.
- Road-tested and re-torqued, with a settling check after the first miles.
Request a quote
Tell us your truck and what you want. We reply with a written quote for the build.