Chevy Silverado Lift Kit
A suspension lift kit for the Chevy Silverado that raises the half-ton for 35s, with the control arms, driveshaft correction and alignment a body-on-frame truck needs to stay steady.
Chevy Silverado Lift Kit at a glance
- Two-inch Silverado lift with spacers and shocks
- $1,200–$2,150
- Two-and-a-half to three-inch Silverado suspension lift
- $1,900–$3,100
- Three-inch Silverado lift with upper control arms
- $2,600–$4,000
- Four-wheel alignment after the lift
- $95–$190
Chevy Silverado lift kit with the corners sorted
A Silverado lift is not a stack of spacers over the strut. Done right it brings the front and rear up together, holds the independent front end inside its range and re-times the steering so the half-ton still runs true at highway speed. Two inches for a taller all-terrain or closer to four for real trail work, the kit has to be cut for the Silverado, not pulled off a shelf.
- Front and rear lift matched so the Silverado sits level
- Corrected arms and steering for the taller half-ton
- Installed, aligned and road-tested before delivery
Chevy Silverado lift kit fitment
The Silverado front and rear changed with each generation, so lift parts do not swap between a K2 and a T1, and a Trail Boss already sits taller. We confirm the year, trim, drivetrain and off-road package before the coil and block numbers are set.
- K2-generation Silverado, roughly 2014 through 2018
- T1-generation Silverado from 2019
- Lift of 2 to 3.5 inches depending on tire size
- Two- and four-wheel drive, WT through High Country, Z71 and Trail Boss
What the Chevy Silverado lift kit includes
On a full-size the springs, dampers and arms carry real weight, so our list is drawn for the Silverado's engine and how the truck is used, never lifted from a lighter pickup.
- Front coil spacers or replacement coil-overs for the Silverado
- Rear lift block or an add-a-leaf for the half-ton leaf pack
- Longer rear shocks valved to the Silverado's weight
- Upper control arms that restore camber range
- Carrier-bearing spacer where the driveshaft angle needs it
- Brake-line brackets, bump stops and a full torque sheet
How we install a Chevy Silverado lift kit
We take the Silverado through a set sequence so it leaves squared, aligned and clear of the shake people pin on lifts.
-
1. Confirm the Silverado generation, trim and target height.
-
2. Measure the ride height and inspect the struts and leaf springs.
-
3. Install the front lift and the corrected upper arms.
-
4. Set the rear with a block or an add-a-leaf.
-
5. Fit the longer shocks and check the brake lines.
-
6. Align camber, caster, toe and thrust at the raised height.
-
7. Road-test, watch for driveshaft vibration and re-torque.
What a Chevy Silverado lift kit costs
A Silverado lift covers the coils, dampers and every geometry part the height forces, and the meter runs hardest past three inches. Numbers shift with the generation and trim, so take the ranges below as a guide and ask us for a firm figure on your truck. The price varies by year and trim.
- Two-inch Silverado lift with spacers and shocks
- $1,200–$2,150 installed
- Two-and-a-half to three-inch Silverado suspension lift
- $1,900–$3,100
- Three-inch Silverado lift with upper control arms
- $2,600–$4,000
- Four-wheel alignment after the lift
- $95–$190
- Rear add-a-leaf for a loaded Silverado
- $450–$1,000
What changes under a lifted Silverado
Past three inches the factory Silverado arms lose their camber range and the driveshaft settles at a steeper angle, which is the real source of the shimmy some lifted half-tons blame on the springs. Corrected arms and a carrier-bearing spacer are how we settle a Silverado back down.
- Camber held where the Silverado can align to it
- Rear driveshaft kept from shuddering under acceleration
- A half-ton that tracks straight instead of hunting the lane
From the bay
Questions about this build
How much lift can a Silverado take?
Two to three inches is the sensible range on a Silverado, because the front suspension keeps travel and the driveshaft angle stays healthy. Past three the half-ton needs corrected arms and driveshaft attention, which we build into the quote.
Will a lifted Silverado ride rough?
It can if the shocks are wrong for the load. We valve the shocks for the Silverado's engine and use quality coils so the truck stays planted without crashing over expansion joints, which is the balance a half-ton lift lives on.
Do I need new upper control arms on a lifted Silverado?
Past about three inches, yes. The stock Silverado arms run out of ball-joint range and cannot hold camber, so corrected arms are the only way to align it. Below that, originals are usually fine.
What tire fits a three-inch Silverado lift?
A three-inch lift usually clears a 35 on a Silverado with the right offset, and a 33 without effort. We check wheel offset and fender clearance on your truck before any tire is ordered.
Can you lift a two-wheel-drive Silverado?
Yes, and a two-wheel-drive Silverado lifts cleanly for stance and clearance. The front hardware differs from the four-wheel-drive kit because the spindles and knuckles are not the same, so we order by drivetrain.
How does a lifted Silverado tow?
Well, when the rear is supported properly. We keep the rear leaf pack working and add a block or an add-a-leaf so a loaded Silverado stays level rather than squatting, which keeps steering light and the trailer tracking straight.
Why Valley drivers bring their trucks here
- Lift, leveling, wheels and alignment under one roof, corrected and aligned.
- Written estimate before any part is ordered, with the extras called out.
- Fitment confirmed on your exact truck before you buy tires or wheels.
- Road-tested and re-torqued, with a settling check after the first miles.
Request a quote
Tell us your truck and what you want. We reply with a written quote for the build.